Author Topic: Smoked 3 P10 boards  (Read 17978 times)

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Re: Smoked 3 P10 boards
« Reply #45 on: May 23, 2015, 03:52:42 PM »
Ok.  All 24 panels now on.


Sent from my iPhone using Tapatalk
Ryan

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Re: Smoked 3 P10 boards
« Reply #46 on: May 23, 2015, 03:53:17 PM »


Now to take them off to make access holes and finalize the mounting.


Sent from my iPhone using Tapatalk

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Re: Smoked 3 P10 boards
« Reply #47 on: May 23, 2015, 06:34:29 PM »


Found a little issue....the power and joining cables don't line up!

So I will need to cut and see if I can get it to line up. Tomorrow afternoons job


Sent from my iPhone using Tapatalk

Offline JonB256

  • Supporting Member
  • ******
  • Join Date: Mar 2013
  • Location: Granbury, Texas
  • Posts: 5,244
  • Kudos: 126
    • Granbury Christmas Lights
Re: Smoked 3 P10 boards
« Reply #48 on: May 23, 2015, 09:09:22 PM »
Sawdust on the floor means you've done good.

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Re: Smoked 3 P10 boards
« Reply #49 on: May 24, 2015, 03:37:25 AM »
I just don't know how i'm going to explain all those cup holders that I built into the back step to the missus.....

  ;D

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Re: Smoked 3 P10 boards
« Reply #50 on: May 24, 2015, 07:59:26 AM »


Ok. Have a row back on after cutting the holes. Now off to do something with the dog and family for a hours and maybe get it back together late this afternoon


Sent from my iPhone using Tapatalk

Offline JerryPlak

  • Supporting Member
  • ******
  • Join Date: Jul 2013
  • Location: Sunbury, OH
  • Posts: 603
  • Kudos: 2
Re: Smoked 3 P10 boards
« Reply #51 on: May 24, 2015, 10:11:34 AM »
:-D no one will see from the front side went you are done ;-)

Sent from my QMV7A using Tapatalk

Jerry Plak

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Re: Smoked 3 P10 boards
« Reply #52 on: May 24, 2015, 02:19:52 PM »


Getting there...


Sent from my iPhone using Tapatalk

Offline JerryPlak

  • Supporting Member
  • ******
  • Join Date: Jul 2013
  • Location: Sunbury, OH
  • Posts: 603
  • Kudos: 2
Re: Smoked 3 P10 boards
« Reply #53 on: May 24, 2015, 02:29:58 PM »
Looking good !

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Re: Smoked 3 P10 boards
« Reply #54 on: May 24, 2015, 03:57:43 PM »
Ok.  A couple of cross braces added and sorted out the power distribution.

Of course this ray wu 70a power supply is sooooo confusing.  I get the LN and gnd power input but the wire is blue yellow and red. Which colour is what?


Sent from my iPhone using Tapatalk

Offline arw01

  • Hero Member
  • *****
  • Join Date: Oct 2013
  • Location:
  • Posts: 891
  • Kudos: 0
Re: Smoked 3 P10 boards
« Reply #55 on: May 24, 2015, 05:50:23 PM »
I would not trust those chinese workers to even get the right wires on the right solder spots.  I took my cover off and looked at the circuit board. I suggest you do the same and write it on the outside in sharpee because you won't remember later!

Alan

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Re: Smoked 3 P10 boards
« Reply #56 on: May 24, 2015, 06:31:27 PM »
Good advice.

Now I won't forget it (:


Sent from my iPhone using Tapatalk

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Re: Smoked 3 P10 boards
« Reply #57 on: May 24, 2015, 07:12:59 PM »
Last pictures of the night.

Have the PSUs wired up to the 24 panels. Will have to go and source a couple of power cables tomorrow. I can't seem to find any spare ones around the basement. Damn spring cleaning (:






Sent from my iPhone using Tapatalk

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Smoked 3 P10 boards
« Reply #58 on: May 25, 2015, 06:49:20 PM »
Well something isn't quite right. I hope it's just how I have the octo setup


Sent from my iPhone using Tapatalkhttps://vimeo.com/128831118

Offline drlucas

  • Developer
  • ******
  • Join Date: Sep 2013
  • Location: Whitby, Ontario - Canada
  • Posts: 1,424
  • Kudos: 3
Re: Smoked 3 P10 boards
« Reply #59 on: May 25, 2015, 07:03:04 PM »
A bit better...but not 100% yet



Sent from my iPhone using Tapatalk

 

Back to top