News:

LATEST RELEASE:  FPP 6.3 - Download from here - https://github.com/FalconChristmas/fpp/releases/tag/6.3

+-+-

+-User

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

+-Site Stats

Members
Total Members: 15659
Latest: PaulDzRGB
New This Month: 9
New This Week: 3
New Today: 1
Stats
Total Posts: 128431
Total Topics: 15791
Most Online Today: 38
Most Online Ever: 7634
(January 21, 2020, 02:14:03 AM)
Users Online
Members: 3
Guests: 19
Total: 22

Warning/Error: Network incomplete frames hit 250.

Started by nmbgeek, November 26, 2022, 03:39:44 PM

Previous topic - Next topic

k6ccc and 1 Guest are viewing this topic.

nmbgeek

Receiving this on the web interface:  
QuoteNetwork incomplete frames hit 250. Network or configuration issue is likely.
My network setup is as follows: PFSense Firewall > Cisco 48 Port Gigabit PoE Switch > Falcon F16v4 > FPP on RaspberryPi.  Everything is wired with CAT6 and all devices have statically assigned DHCP addresses (devices are set to DHCP and router hands out the static IP) and they are working as expected.

I also have an ESP32-POE connected to the Gigabit switch for permanently installed roof outline.  It is also receiving data from FPP and working as expected. Lights seem to be functioning as desired but I do notice some 'jumps' in my show.  Never saw this message last year but I did update firmware when I pulled everything out this year.  The message does stop when a show is not playing.

Any advice or troubleshooting suggestions?

JonD

I had that problem on firmware version 21.  Downgraded to version 20 and it fixed it.

nmbgeek

Thanks for that info. I may try downgrading tomorrow then. 

JonD

I just logged into the controller and it is still getting the error... just not as bad.   Noticed some lag on fast sequences when on 21, but have not noticed anything since downgrading.  I may have the same issue as you though.

newtoitall

Morning,

Newbie here.  I'm having the same issue and I am only running two props.  I don't see it affecting the show, does anyone know if will damage the controller?

Another question and I apologize, my computer skills are lacking.  But when you say you downgrade the firmware, are you talking about the firmware for the FPP?

Thanks for any help in advance.

pck

Same problem here. I have been running build 21 on my Falcon F48V4 since Dec 4th without this error. The error started showing up yesterday (Dec 30th). It comes and goes, but does not appear to affect my displays.

jnealand

To me that is just a warning that your show is having some issues getting all the data out.  And it has happened 250 times or more.  I would be checking all my connections for being loose or for corrosion as a place to start.  Just dmy 2 cents.
Jim Nealand
Kennesaw, GA all Falcon controllers, all 12v Master Remote Multisync with Pi and BBB P10 and P5

pck

Thanks Jim. It really helps me if I know what the error means. I think I found the problem.

All of my equipment (network and pixel controllers) is in my garage and located within a few feet of each other.

I had another issue which I never was able to figure out with my Falcon Pi Player. It would only work when plugged into the Falcon Controller's ethernet pass-thru port, not my switch (tried different cables). The guys on the Xlights Zoom Room reviewed my configuration, but I still couldn't get it to work. Not a big problem so I left it connected to the F48V4.

While trying to fix the  "Network incomplete frames hit 250" I discovered that one of my ethernet switches was a hub, not a switch, and my show ethernet switch was being fed by a ethernet hub instead of a switch. I switched the hub out to a switch and both problems have gone away.

Thanks for your help. Happy new year!

joeyblasko

I am having this same issue, but with the new F48v4NS controller.  The build on the controller is Build 23, which is not available from GitHub, so I am reluctant to downgrade my firmware version since, if it doesn't work, I can't restore it to its original condition.  I have checked all my cabling, replaced my router with a switch and all the things mentioned in this post, but to no avail.  Any other folks have ideas on how to correct the error?

Thanks in advance.

J

jnealand

If I recall correctly 23 was removed because of problems.  I would go back to 22 if you can.
Jim Nealand
Kennesaw, GA all Falcon controllers, all 12v Master Remote Multisync with Pi and BBB P10 and P5

Poporacer

Quote from: jnealand on February 05, 2023, 02:19:10 PMIf I recall correctly 23 was removed because of problems
That was for the regular F48V4, the NS one needs 23
If to err is human, I am more human than most people.

darylc

Build 23 is the first version to support the F48v4-NS, I don't it will let you downgrade.

JonD

Version 22 is the one you should delete and never use.  I still have the issue with my Mega tree controller having this error.  I can tell it is lagging on occasion, but it was really cold out when I noticed it and told my wife she can just refund anyone that complains about it. (We don't charge for people to watch the display ;))

Support FPP

+- Recent Topics

Warning/Error: Network incomplete frames hit 250. by JonD
February 06, 2023, 04:10:22 PM

F16V3 with 2 expansion boards at 40 fps MAX PIXELS per output? by tbone321
February 06, 2023, 10:51:55 AM

F48V4-NS at 40 fps using all 48 pixel output ports? by Poporacer
February 06, 2023, 10:27:09 AM

Unable to update RPi 5.5 to latest version by JonB256
February 05, 2023, 07:23:16 PM

help getting started, next step? by rayster
February 05, 2023, 04:24:09 PM

F48v4NS - Pi or No Pi? by joeyblasko
February 05, 2023, 09:15:33 AM

Huidu Controllers LED matrix by CaptainMurdoch
February 04, 2023, 10:18:47 AM

FPP6.2 universes by darylc
February 03, 2023, 08:48:57 PM

F16v4 Ports vs Universe Configuration Question by k6ccc
February 03, 2023, 09:32:48 AM

Need Expert Advise on F16v4 Ports vs Universe Configuration by Kairus
February 03, 2023, 09:32:33 AM

Powered by EzPortal
Powered by SMFPacks Menu Editor Mod