Recent Posts

Pages: 1 ... 3 4 [5] 6 7 ... 10
41
Showing Off / Re: Enclosure builds are 100% complete.
« Last post by Xmas! on February 20, 2019, 07:03:13 PM »
They look neatly built.  One thing I did notice however was the use of an IEC C14 inlet for the mains.  Will these enclosures be outdoors?

They will all be protected from the weather except the smallest enclosure with just a diff rec.
42
Falcon Player Plugins / Dante audio protcol over IP
« Last post by sklankowski on February 20, 2019, 06:58:46 PM »
I have a unique application with operation in large park setting, but I have been trying to find a better method of creating a single distributed sound throughout various display areas without using FM broadcasting and reamplify.  I was told that if I was to use the audio from a remote Pi that it would likely be stuttering due to timing corrections.  I have been looking at plugins that stream audio, but that would a device to process that stream.  lately, I  have been looking at Dante audio network equipment, to utilize a USB to IP adapter from FPP and cast it across a network (will have hard line IP to large props).  I am trying to search for code/scripts to enable the FPP to send out a Dante protocol signal, but I could experiment with the USB and physical adapters. 
Curious if someone could help on this pursuit to add feature. Found a project that is closely related to my desire, but lack more indepth coding knowledge.      https://github.com/jsharkey/wycliffe
43
Showing Off / Re: Enclosure builds are 100% complete.
« Last post by Todd on February 20, 2019, 06:18:28 PM »
Very nicely done Xmas.
45
So no problem running 10amps on the input header?

I don't know of any issues.  The outputs are fused at 5A each and I believe the board is designed to handle it.

If you have any concerns, you can always power inject right at the PiCap and just run the data and ground lines from the PiCap to the first pixel with the power and ground from the first pixel connected to a fused power source.
46
Showing Off / Re: Enclosure builds are 100% complete.
« Last post by Emuney18 on February 20, 2019, 04:57:52 PM »
What is the model of the little box?


Sent from my iPhone using Tapatalk
47
The strips say you don't need to inject but I did notice the end of the strip was not behaving properly.  Limiting the brightness solved the issue.  In hindsight it would have been a good idea to inject power but its probably too late now.  Ive got them all assembled and these is no way to run a wire at this point.  If I make another set I'll keep that in mind.  For now, limiting the brightness in FPP sounds like a good solution.

So no problem running 10amps on the input header?
48
For the 60 leds / m you will most liky have to power inject.
49
Showing Off / Re: Enclosure builds are 100% complete.
« Last post by David_AVD on February 20, 2019, 03:02:20 PM »
They look neatly built.  One thing I did notice however was the use of an IEC C14 inlet for the mains.  Will these enclosures be outdoors?
50
Falcon Group Buys / Re: [GROUP BUY] BeagleBone/PocketBeagle based controllers
« Last post by TypingOffKey on February 20, 2019, 02:54:48 PM »
ItemQtyCostTotal Cost
F8-B0$48$0
F32-B0$92$0
F8-PB1$48$48
F40D-PB0$41$0
PocketScroller0$16$0
PocketBeagle1$30$30
Shipping$8
Total$86

Thanks Dan!
Pages: 1 ... 3 4 [5] 6 7 ... 10
Back to top