FPD no output tab FPP3.0

[wftxlites]

Ok, should I leave it on master branch?
-- Logs begin at Sat 2019-08-24 16:29:39 CDT, end at Sat 2019-08-24 16:32:19 CDT. --
Aug 24 16:30:22 FPP systemd[1]: Starting FPPd...
Aug 24 16:30:26 FPP fpp_boot[637]: Checking config version
Aug 24 16:30:26 FPP fpp_boot[637]: FPP Version: 31
Aug 24 16:30:26 FPP fpp_boot[637]: Config Version: 52
Aug 24 16:30:26 FPP fpp_boot[637]: Up to date at config version 52
Aug 24 16:30:28 FPP fpp_boot[637]: FPP - Checking for configured LCD, LCD Disabled
Aug 24 16:30:31 FPP fpp_boot[637]: FPP - Found IP(s): 192.168.1.135
Aug 24 16:30:31 FPP fpp_boot[637]: FPP - Setting up SPI
Aug 24 16:30:31 FPP fpp_boot[637]: FPP - Checking for PiFace
Aug 24 16:30:32 FPP fpp_boot[637]: /dev/spidev0.0
Aug 24 16:30:32 FPP fpp_boot[637]: /dev/spidev0.1
Aug 24 16:31:00 FPP fpp_boot[637]: FPP - Checking for Falcon hardware on SPI port
Aug 24 16:31:03 FPP fpp_boot[637]: 2019-08-24 16:31:03 (1200) falcon.c:224:FalconDetectHardware(0xbef83898)
Aug 24 16:31:03 FPP fpp_boot[637]: 2019-08-24 16:31:03 (1200) falcon.c:550:FalconDetectHardware response size 32774
Aug 24 16:31:03 FPP fpp_boot[637]: 2019-08-24 16:31:03 (1200) common.cpp:113:Falcon Detect Hardware Response: (8 byt
Aug 24 16:31:03 FPP fpp_boot[637]: 2019-08-24 16:31:03 (1200) common.cpp:168:000000: 02 00 00 00 00 00 00 00
Aug 24 16:31:03 FPP fpp_boot[637]: 2019-08-24 16:31:03 (1200) falcon.c:586:Falcon Hardware Detected on SPI port 0
Aug 24 16:31:03 FPP fpp_boot[637]: 2019-08-24 16:31:03 (1200) falcon.c:587:    Model           : FPD v1.x
Aug 24 16:31:03 FPP fpp_boot[637]: 2019-08-24 16:31:03 (1200) falcon.c:588:    Firmware Version: 0.0
Aug 24 16:31:04 FPP fpp_boot[637]: FPP - Turning OFF screen blanking
Aug 24 16:31:10 FPP systemd[1]: Started FPPd.

[dkulp]

Well, that shows that it DID detect the FPD.   If you turn off the "Show all options" box, does the page disappear now?

[wftxlites]

Unchecked and rebooted. Tab is missing! Ran the SUDO command again and it says detected. Also, one interesting thing is that FPD is outputting data and working.

[dkulp]

Can you do a manual update, reboot, and repost the log?    I'm trying to figure out why it's detecting it, but not recording it's detected properly.


Also, can you do a "cat ~fpp/media/settings" and let me know what the FalconHardwareDetected setting is set to when done?

[wftxlites]

Checked and Tab is still missing.

fpp@FPP:~ $ cat ~fpp/media/settings
storageDevice = "mmcblk0p2"
LastBlock = "14983168"
PiFaceDetected = "0"
FalconHardwareDetected = "1"
rebootFlag = 0
restartFlag = 0
volume = "100"
AudioCard0Type = "bcm2"
wifiDrivers = "Kernel"
MultiSyncRefreshStatus = "1"
piRTC = "N"
ntpServer = ""
HostName = "FPP"
TetherSSID = "FPP2"
FPDEnabled = "1"
e131statsLiveUpdate = "1"
EnableRouting = "0"
AudioOutput = "0"
AudioMixerDevice = "PCM"
MultiSyncRemotes = "192.168.1.134"
CompressMultiSyncTransfers = "1"
Latitude = "33.865571"
Longitude = "-98.543958"
fppMode = "player"
showAllOptions = "0"

[dkulp]

OK.  I was looking in completely the wrong place.   Should be fixed now.

[wftxlites]

Sorry to be a pain, but I still don't see the tab. Updated, rebooted, started and stopped FPPD then checked again. Then I checked the box again and I see see it, but not checking box automatically. Maybe there is something else I need to do.




BTW this is not something that has to be fixed right now. I'm good to use the checkbox. Just hit this thread or PM me the next time you need testing on this.


Thanks for your help,


Greg

[RichM]

I just updated my pi to fpp3.3 with an attached FPD (previously on 2.x masterbranch). The tab to setup the FPD did not show up. I had to go into advance settings and check box "show all options". Thanks to this thread I now know what to do. Thank you.